Automated testing for embedded devices: a practical guide for startups
When you think of automated testing in embedded systems, you might imagine racks of test hardware, robotic arms, and blinking boards in a corporate lab. For startups - often juggling deadlines, limited budgets, and evolving hardware - that can feel completely out of reach.
But should it be? Is automated testing in embedded only for big teams with deep pockets - or can startups actually benefit from it too?
Let's break down what it really takes, where the challenges lie, and why it's still worth doing.
1. The three levels of firmware testing
Setting up automated testing for firmware isn't like running unit tests on a web app. Part of your code can be tested that way. The rest only shows its bugs on real hardware. That's why automated testing for embedded devices works best on three levels, each catching a different kind of bug.
Host-based unit tests
You compile your C modules with the host compiler and run them on a laptop or a CI runner, with the hardware layer replaced by mocks. They catch logic errors - parsers, state machines, protocol framing, ring buffers, calculations - in seconds, without a board.
What they can't catch is anything that depends on the MCU itself: peripherals, interrupts, timing, or the differences between your host compiler and the target toolchain.
When to add them: from the first module that has logic worth testing. They're cheap, fast, and can run on every commit.
On-target tests on the MCU
The same tests, or a dedicated test firmware, cross-compiled and run on the real microcontroller - often a dev board at first. Results come back over UART or the debug probe.
They catch what the host hides: integer sizes and alignment, stack usage, compiler differences, and drivers talking to real peripheral registers.
When to add them: once you write your own drivers, or once a vendor HAL sits under something critical.
Hardware-in-the-loop tests on a real bench
The firmware you ship runs on the board you ship, and the test drives it from the outside - the way the field will. This level catches what only the whole device shows: boot and bootloader problems, communication on the real bus, behavior after a power cycle, current draw, and reset or boot pins wired the wrong way.
It's also the level that makes people think of corporate labs, because you have to build a setup that can physically interact with your devices. You'll need a way to:
- Power, flash, and reset boards remotely.
- Measure signals, voltages, or communication lines.
- Sometimes even include external reference devices like encoders, temperature sensors, or programmable loads that validate how your system behaves.
When to add them: as soon as you have a board your customers will touch. One test of the interface they use most is enough to start.
Even after everything is up and running, the system needs maintenance: firmware versions change, interfaces evolve, and test setups occasionally fail. Automation, ironically, still requires humans to keep it healthy.
2. The early slowdown effect
There's no denying it - at first, automation slows you down.
When you add CI pipelines and test stages:
- Builds take longer.
- Merge requests wait until pipelines pass.
- Engineers may grumble that they're testing "unrelated" features.
And sometimes, they're right - not every test is relevant to every change. But in practice, bugs rarely respect boundaries.
A small tweak to a shared utility or timing function can quietly break a completely different driver. A minor refactor in one module can ripple across the system in ways nobody expected. The truth is, the more people that touch the codebase, the greater the need for automated checks to keep everything consistent.
Automation isn't about bureaucracy - it's about protecting development speed long-term. You might lose a few minutes to pipeline runs today, but you'll save days of debugging tomorrow.
3. Collaboration through test definitions
One underrated advantage of automated testing is how it improves communication and understanding within the team.
When writing tests becomes part of the development process, engineers must define what "correct behavior" actually means - together. This shared understanding reduces misunderstandings and makes code reviews more meaningful.
In fact, during a code review, starting by reading the test definitions is often the best way to check if everyone understood the feature in the same way. If two engineers imagine different outcomes, the test will reveal that instantly - long before the bug reaches hardware.
4. When to start, and the tools for embedded test automation
Many teams think they should wait until the system is mature before automating tests. But in reality, the sooner you start, the better.
Once you have your first main loop and the firmware compiles, it's worth setting up a basic CI pipeline that:
- Builds the firmware.
- Runs static analysis or linting.
- Runs host-based unit tests.
- Maybe checks code formatting or documentation.
That's already a foundation.
There's no universal framework for embedded testing, so you'll assemble your own test environment. You don't have to write it from scratch, though. A small, common toolset covers most of it:
- Unity and Ceedling for C unit tests. Unity is a small C test framework that runs on the host and on the MCU. Ceedling builds and runs Unity tests and generates mocks of your hardware layer with CMock, so a driver call becomes an expectation you can check.
- pytest for driving hardware tests. Python is the easiest way to talk to a board: send a command over the serial port, read the response, compare it with what you expect. pytest fixtures handle the setup - power the board, flash the build - and every test ends as a pass or fail your CI understands.
You may also run into commercial tools such as VectorCAST or Parasoft C/C++test. They automate unit and integration testing of embedded software and report code coverage, which matters in safety-critical projects. They test your code unit by unit, on the host or on the target. A test on real hardware tests the device: it powers the board, flashes the build, and checks what comes out of its pins and buses. One doesn't replace the other - they're separate stages of the same pipeline.
When it comes to hardware testing, you don't need to go all in from day one. Start with what's most accessible: for instance, verify the communication interfaces your clients will use first - UART, CAN, SPI, or USB. Make sure these always behave as expected.
From there, you can add more complex, environment-dependent tests - things involving motors, sensors, or external measurement devices - as your product matures.
5. The real cost of not testing
Many startups delay investing in testing because they're focused on getting a prototype working quickly. That's understandable - but it has a hidden cost.
Without automated tests:
- Bugs get discovered later, when they're harder and more expensive to fix.
- Regression issues sneak in, breaking features that used to work.
- Customer demos can fail unexpectedly because edge cases weren't caught.
- Engineers lose confidence in making changes, slowing down development over time.
For a startup, time is the most valuable resource. Automated testing might feel like a drag early on - but it ultimately buys you time. It prevents hours of debugging, reduces customer complaints, and gives your team the confidence to move fast without breaking things.
6. Start small: automated firmware testing in CI
You don't need a perfect test setup on day one. Start with what's practical and expand as you go:
- Week 1: Set up a CI pipeline that builds your firmware, runs basic static checks, and runs your first host unit tests.
- Month 1: Add your first hardware test - maybe a simple UART communication check.
- Month 3: Expand to test the key features your customers rely on - power cycling, error handling, or interface stability. Run your unit tests on the target, too.
- Month 6: Start running nightly regression tests to catch issues over longer time scales.
The hardware stage from month 1 is less exotic than it sounds. It runs right after the build job and does five things:
- Reserves the test bench, so nobody else touches the board during the run.
- Flashes the binary the build job just produced, so every result belongs to a known commit.
- Power-cycles the board, so each run starts from a clean boot.
- Runs the pytest suite: send commands over UART, read the responses, and check the log for the boot message, the right firmware version, and no error lines.
- Marks the job as passed or failed and attaches the UART log, so a failure can be read without the board.
This is where some DevOps knowledge comes in. The classic setup is a self-hosted CI runner with the board plugged into it over USB. It works, but it ties your pipeline to one machine on one desk, and someone has to keep that machine healthy.
If the bench can be driven over an API, the hardware stage is just another script. Any CI that can call an API - GitLab CI, GitHub Actions, Jenkins - can run it, and the runner doesn't need to be wired to the board. That's how WisentWire brings tests on real hardware into CI: a CoreUnit at the bench flashes, powers, and talks to the board, and your pipeline drives it through the REST API or the Python SDK.
Every step makes your system more reliable and your team more efficient. And the sooner you start, the more you benefit.
Conclusion
Can startups do automated testing in embedded? Absolutely.
It's not easy, and it won't feel fast at first - but neither is building reliable hardware. Testing is an investment in quality, confidence, and long-term development speed.
You don't need a corporate-level test lab to get started. You just need to begin - one test at a time.

